How to solve the problem of pulling the UV flat panel

date :2018-1-26 15:09:23hits :61author:郑州乐彩

 Nowadays, UV flatbeds have been used in many industries and have been well received by users. However, the pull problem of the uv flatbed printer is also a small situation that occurs when the daily care is not taken care of. This article will give you a detailed explanation of the causes and solutions of the pull cable.

 Abnormal pull:

 Auxiliary equipment abnormal nature pull line: refers to the lack of ink between the entire nozzle or a continuous number of spray points. The reason for this kind of pulling is that the nozzle does not emit ink or the ink of the UV flatbed printer is insufficient, or the ink is stuck on the nozzle due to the instability of the UV flatbed printer. However, most of these pull wires are usually caused by nozzle circuit boards or negative pressure pumps and ink supply pumps. In general, replace the corresponding circuit board and vacuum pump. Of course, there is also a way to increase the frequency of the ink supply pump and periodically replace the filter to eliminate the abnormal nature of the auxiliary equipment.

 Feather pull line:

 Feather pull line: This kind of pull line is generally realized by the arrangement of the nozzles in the direction of the apparently equidistant arrangement or the white line. The state diagram of the print head can observe that the stitching positions are overlapped, spaced or poorly feathered. Such a pull wire only needs to check and adjust the belt to make the UV flatbed printer operate normally, and adjust the nozzle's spray point transfer position or adjust the feathering to solve. However, it should be noted that in the case of different grayscale graphics printed, the degree of feathering required for the same handover location may be different.

 Blocking cable:

 The pull wire of the plugging property: the UV flatbed printer pull wire of this nature is generally a "white line" of a certain color channel fixed position, and there are many "white lines" in severe cases. The reason for the blockage is that there are many aspects. For example, the operation mode and environmental factors will cause the pull line of the plugging property. The uv ink shakes the ink unevenly. During the process of adding the uv ink, some impurities are introduced. When the wipe is cleaned, the nozzle is not standardized, so that the dust of the environment adheres to the nozzle. . Use a sponge to clean other inks such as ink or glaze powder when cleaning and maintaining the nozzle.

   Tips:

 When users use UV flatbed printers, pay more attention to observe, pay attention to daily cleaning to reduce the occurrence of cable problems, even if it does not need to be anxious, according to the above method, your own operation can be quickly resolved.



 

  Zhengzhou Locor Technology Co., Ltd. has a registered capital of 26 million RMB. The company has a young, efficient, united and innovative elite team, and an entrepreneurial environment that catches up with the international advanced level, leads the development of the Chinese industry.

 Locor pays attention to the research and application development of independent technology in the field of printing equipment,has established a company technology research and development center, equipped with advanced equipment and testing instruments with a good R&D experimental environment. The company's technical department cooperates with many research institutes at home and abroad, uses the current new micro-electromechanical and micro-electronic technology to conduct exploratory research and development. It is used in printer print head drive analysis, rack manufacturing, testing, control system design, trial production, etc. Unique insights and innovative inventions.

    Locor has applied for 51 patents related to digital printing equipment, including 3 invention patents; in 2008, the company was recognized as a high-tech enterprise by Henan Science and Technology Department, has passed the EU CE certification in 2008; in May 2010, Zhengzhou Development and Reform Commission Approved the establishment of Zhengzhou Digital Wide-format Printing Equipment Engineering Research Center and listed it in the National Twelfth Five-Year Plan for Electronic Information Industry; In June 2010, it officially started the shareholding system reform and became the first batch of new three-board enterprises in Zhengzhou High-tech Industrial Development Zone.

At present, Locorproducts and service organizations have covered more than 80 countries and regions in 31 provinces and cities in China and overseas; Locor are willing to work together with friends in the industry to provide satisfactory products and services for domestic and foreign customers!

 

Communicate onlineMore contact